PEGACRIL WG07 is a two-component epoxy-polyurethane adhesive indicated for gluing Vitroflex Wallguard on non-porous surfaces and for rubber, PVC and linoleum floors. PEGACRIL WG07 is a two-component adhesive formed by an epoxy-polyurethane polymer, component A and a special hardener, component B. By carefully mixing its two components, a paste of uniform color is obtained, easily applied with a toothed spatula, ideal for application Vitroflex Wallguard on non-porous surfaces.
After hardening (approx. 24 hours) which occurs by chemical reaction and without shrinkage, PEGACRIL WG07 becomes elastic.
Resistant to atmospheric agents.
High adhesion characteristics in almost all materials normally used in construction.
High tenacity and elasticity adhesive for general use, especially suitable for non-absorbent or moisture-sensitive substrates.
Interior and exterior gluing of Vitroflex Wallguard on non-porous surfaces.
Interior and exterior gluing of rubber, PVC, textile, chipboard, linoleum, polystyrene and polyurethane panels, fiber cement, wood, metal sheets, plastic laminates.
Cement, asphalt and non-absorbent or water-sensitive elastic supports (metal sheets, plastic laminates, fiber cement, rubber, PVC, wood, old ceramics).
Rubber flooring in rolls or tiles (with smooth, rough or patterned back), inside and outside, subject to heavy and intense traffic.
Rubber sports flooring, even on asphalt (eg light athletics tracks).
Synthetic grass flooring.
Homogeneous and heterogeneous PVC flooring with PVC foam backing.
Semi-flexible vinyl flooring.
Textile, agglomerate and textile flooring placed outdoors.
Rubber and PVC flooring on old existing flooring.
Sandwich panels for mobile prefabricated walls made of polystyrene, expanded polyurethane, fiber cement, wood, wood conglomerates, metal sheets, etc.
The pieces to be treated must be free of tension, thus avoiding micro-cracks due to the action of the solvent.
The screeds must be uniformly dry, flat absorbent, resistant to compression and traction; be free of dust, detached parts, cracks, varnishes, waxes, oils, rust, remains of plaster and products that may impair adhesion.
The moisture content must be as prescribed: for cementitious screeds a maximum of 2-2,5%, for those based on gypsum or anhydride, a maximum of 0,5%.
It is essential to ensure that there are no rises of humidity. Floating screeds or on layers of lightening or insulation and screeds on embankments must be insulated with a vapor barrier.
Before starting the installation, make sure that the flooring, the covering, the adhesive and the screed are acclimated to the prescribed temperature.
The floor and wall tiles must be removed from the packaging a few hours before laying; The pieces must be spread freely or, at least, the rolls should be loosened to allow acclimatization and the reduction of stresses due to packaging.
Application with a notched trowel or 2mm spatula
The two components of PEGACRIL WG07 are supplied in containers in proportion to their dosage. Mix ratio: comp. A: comp. B = 94: 6. A. Component A - 9,4 parts by weight B. component B - 0,6 parts by weight
Duration of mix: 50-60 minutes.
Setting time: 9 hours.
Commissioning: after 3 days at + 23 ° C.
Mixing must be done with a mechanical stirrer until a homogeneous paste is obtained.
Setting speed and pot life are closely linked to room temperature.
Never work at temperatures below + 10 ° C so that the setting does not take too long.
Attention: the relationship between the resin (component A) and the catalyst (component B) is precise.
Any modification of the dosage compromises the crosslinking of the product.
Apply the adhesive evenly and on a surface that can be covered with the coating in approximately 60 minutes in relation to the ambient temperature and the screed.
Consumption and storage:
Consumption: 0,5-0,7 kg / m². (15-20m2 per container).
It is important not to skimp and that there is a minimum thickness to guarantee the elasticity of the union between the two materials.
Storage: 24 months.
Presentation: 10 drums
Do not apply on wet concrete (residual humidity must not exceed 3,0%).
Do not apply on fresh asphalt (wait at least 20 days).
Do not apply on bituminous surfaces that have the possibility of oil exudation.
Do not use PEGACRIL WG07 at temperatures below + 10 ° C or above + 30 ° C.
SAFETY INSTRUCTIONS FOR THE PREPARATION AND APPLICATION
● PEGACRIL WG07 component A is irritating to the eyes and skin.
● PEGACRIL WG07 component B is corrosive and harmful in contact with the skin and if swallowed. ● Both components can cause skin contact sensitivity in subjects predisposed. ● Wear suitable protective clothing and gloves and protect eyes and face. ● In case of contact with the eyes and skin, wash immediately with plenty of water. On In case of ingestion and in the most serious cases, consult a doctor. ● Use in sufficiently ventilated places. Both components are dangerous for aquatic organisms: avoid spreading the product in the environment. ● For more information consult the Safety Data Sheet.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may be necessary for the website to function and is used to collect personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.